At a given gross weight, increase in density altitude (DA) means a reduction in engine horsepower (thus a reduction in thrust), increased ground speed (thus longer takeoff and landing rolls), and decreased climb performance. The changes can be significant, especially at higher elevations. 
photo by Amy Hoover

A turbocharger can solve some of the problems (except with your pocketbook). However, loss of propeller efficiency is a big factor, even on turbocharged aircraft. If your summer flying takes you to the mountains, you will learn to operate in the morning or late evening when your engine, propeller, and wings perform better. A major item you can control is how you load your airplane; you determine is how you load your airplane.
When you operate at higher elevation airports in the heat of the summer, do you have a handle on how much weight reduction is necessary for safe operations? How often do you really know just what you can expect from your airplane at higher density altitudes? Your aircraft performance charts are a good place to start. However, many charts only give performance figures at gross weight, and some older aircraft substantial charts or data. Remember that you are not flying a new airplane and your performance will probably not meet the expectations of the charts.
photo by Amy Hoover  An excellent method of determining effects of density altitude is to build your own performance charts. Load your airplane to different weight and Center of Gravity positions and record takeoff and landing distances at different density altitudes for each weight/CG combination. This requires some time commitment, but is worth it. Use a runway where you have references, such as spacing of runway edge lights, to be as accurate as possible in recording takeoff and landing distances. You may need to factor in other variables such as runway gradient, runway surface conditions, and wind. If you get the chance, attend a density altitude clinic, such as the ones sponsored by the FAA, to collect data on your aircraft performance. 
Determining Density Altitude (DA):
Following is a simple way to determine density altitude (DA) at a given pressure altitude (PA):
Rule of thumb: To determine DA at a given PA, add 600 feet to existing PA for every 10° F above standard temperature for that altitude. 
To do this, you must know the standard temperature at a given PA as shown in the table to the right. You should know the standard temperature for your home field and otherelevations you use often. 
Pressure altitude......... Standard temperature
Sea level....................59.0° F.............15° C 1000 feet ....................55.5° F.............13° C 2000 feet ....................52.0° F.............11° C 3000 feet ....................48.5° F...............9° C 4000 feet ....................45.0° F...............7° C 5000 feet ....................41.5° F...............5° C 6000 feet ....................38.0° F...............3° C 7000 feet ....................34.5° F...............1° C 8000 feet ....................31.0° F..............1° C 9000 feet ....................27.5° F..............3° C 
Example: Pressure altitude (PA)...............= 5000 feet Temperature.............................= 85° F Standard temp at 5000 ft...........= 41.5° F Temp = 85  41.5......................= 43.5° above standard Using the Rule of thumb, round off the numbers to make it easier: Density altitude (DA).................= 5000 + (600 x 4.4) ...............................................= 5000 + 2640...............................................=7600 feet 
Another example: PA..........................................= 9000 feet Temp......................................= 70° F Standard temp at 9000 feet.......= 27.5° F Temp .....................................= 70  27.5 ..............................................= 42.5 degrees above standard Density Altitude (DA)...............= 9000 + (600 X 4.3)..............................................= 9000 + 2580..............................................=11,600 feet 
Reduction in engine horsepower due to DA increase:
As density altitude increases, engine horsepower decreases. If you know what the decrease is and how to apply that knowledge, you can determine roughly what your performance degradation will be and how much weight you may have to take out of the airplane to operate safely. The following is based on standard atmospheric pressure lapse rate and reciprocating engine efficiency.
Rule of thumb: A normally aspirated aircraft engine loses approximately
3.5% hp per 1000 feet increase in DA 
Let's use a common airplane as an example, a Cessna 182.
Example: 230 hp airplane at the 5000 ft airport where the DA = 7600 feet HP reduction.................= 3.5% x 7.6 ....................................= 27% reduction (approximately 73% available) 230hp x (73%)...............= 168 hp available at 7600 ft DA 
Another way to determine the amount of power reduction is to know what your engine will produce at full power on the MP gauge at sea level on a standard day. Then, determine the amount of power per inch it is producing, and calculate power reduction based on the fact the engine will lose one inch of manifold pressure per 1000ft DA.
Example: given a 230hp engine that produces 28" MP at full power, sea level standard day Horsepower per inch..................= 230hp divided by 28" ...............................................= 8.2 hp per inch At 7600 ft DA the engine will produce approximately 20.4" (28"  7.6") at full power and the horsepower will be: 8.2 hp per inch X 20.4"..............= 168 hp available at 7600 ft DA 
Either of the above methods work in estimating your power reduction and give similar results. The amount of reduction may seem a shock at first, but it should alert you to the realities of density altitude related performance problems.
The next question is, how much weight must you remove to compensate for the reduced power if you want to operate at a roughly equivalent sea level performance? One way to do this is do determine the aircraft power loading at which you want to operate, and load the aircraft accordingly. 
Power loading and weight reduction
Sea level standard day power loading is defined as gross weight (GW) divided by horsepower available. In many of the newer Owners manuals or Pilots Operating Handbooks sea level power loading is given with other performance figures, but it is easy to calculate. Using the Cessna 182 again:
Example: The Cessna 182 is A 2950lb, 230hp airplane at sea level:
Power loading ......................= 2950lb......= 12.8 lb/HP...............................................230HP
To get sea level power loading out of the airplane at higher density altitudes, you would have to remove enough weight such that the new weight to hp ratio equals 12.8 lb/HP. To do this, first compute net HP for density altitude:
From the previous example:.....5000 ft PA and 85° F
Density altitude......................= 7600 ft
Horsepower available..............= 168 hp
Original (certified) GW............= 2950 lbs
To calculate the "effective" gross weight that will give equivalent power loading, multiply the net HP available by the desired sea level power loading:
net HP available x SL power loading........= new GW ..............168hp x 12.8...........................= 2150 lbs
Thus to obtain sea level equivalent power loading for the Cessna 182 on a summer day at 5000ft elevation and 85° F you must remove roughly 800 lbs!! That is equivalent to two 180lb passengers, two 75lb bags, and 48 gallons of gas!
The calculation may be done using any power loading you choose to get an approximation of the expected performance. For example, if you usually operate from a 3000ft elevation airport and the performance there is adequate, simply calculate the power loading using 3000ft pressure altitude and standard temperature, and use that figure as the standard of comparison.
Aircraft loading and weight are items over which pilots have direct and immediate control. We have looked at how to reduce aircraft weight to get better performance. However, you may choose to fly with a given weight and accept the decrease in performance. If so, you should have a good idea of just what that decrease in performance is going to be. If an aircraft has inadequate performance charts, you may choose to make your own, as suggested earlier. Or, you may have to make some choices, such as flying only in the morning or evening, or making multiple trips carrying lighter loads.
The bottom line is, be aware of the effects of density altitude on the performance of any aircraft, and learn to lighten up!!
Author: Amy L. Hoover
No comments:
Post a Comment